Atarimax Product Discussion Forums https://www.atarimax.com/flashcart/forum/ |
|
MyIDE Media Compatibility List (Please post reports here) https://www.atarimax.com/flashcart/forum/viewtopic.php?f=7&t=430 |
Page 2 of 3 |
Author: | shagrath [ Wed Aug 08, 2007 4:25 pm ] |
Post subject: | |
Was it compatible?: Yes Manufacturer: Conrad Electronic (http://www.conrad.com) Media Type: Compact Flash Model Number: 974515 - 89 Capacity: Dependent on what you plug into it Interface: MyIDE+1MbFlash Notes: Does not work without a separate power source ! |
Author: | ponderosa [ Fri Dec 12, 2008 4:59 pm ] |
Post subject: | |
Was it compatible?: YES and NO Manufacturer: TRANSCEND Media Type: IDE Flash Module Model Number: TS1GDOM40V-S Capacity: 1GB Interface: MyIDE+1MbFlash Notes: 1GB 40P IDE FLASH MODULE. SMI (V) Around $20 shipped from http://www.transcendusa.com./Products/M ... 6&LangNo=0 I had a little trouble getting this to work reliably on the first computer I tried (130XE). It worked perfectly on my PC with external power and myidetool so I knew the drive was ok. I was worried that it might be trying to draw too much power from the 8-bit. However, I put it on a stock 65XE and it worked great. It also tested fine on an XEGS. Then, I tested it on another 130XE, and it had numerous read/write errors(similar to the first 130XE). I tried it with several different power supplies (just about every type of p/s except the big XE versions). Still no luck. Does the 512MB Transcend work any better with 130XEs? |
Author: | _The Doctor__ [ Fri Dec 12, 2008 11:38 pm ] |
Post subject: | timing issues |
Please make sure you 130XE's have the timing mod done and the sio pin 3 cap clipped. It is something Atari caught and fixed on only the last XE's that shipped so most 130's need it done. and not only for the MyIDE but also for the MIO, BlackBox and higher speed disk drives like the us doubler happy and indus gt drives ultraspeed sio needed mod is here http://www.cs.xu.edu/~ryanr/atari/doubler.html PBI timing mods are here http://nleaudio.com/css/stabiliz.htm and if you 600xl/800xl seem different then look here for alt instructions http://www.mathyvannisselroy.nl/modstab3.txt ponderosa wrote: Was it compatible?: YES and NO
Manufacturer: TRANSCEND Media Type: IDE Flash Module Model Number: TS1GDOM40V-S Capacity: 1GB Interface: MyIDE+1MbFlash Notes: 1GB 40P IDE FLASH MODULE. SMI (V) Around $20 shipped from http://www.transcendusa.com./Products/M ... 6&LangNo=0 I had a little trouble getting this to work reliably on the first computer I tried (130XE). It worked perfectly on my PC with external power and myidetool so I knew the drive was ok. I was worried that it might be trying to draw too much power from the 8-bit. However, I put it on a stock 65XE and it worked great. It also tested fine on an XEGS. Then, I tested it on another 130XE, and it had numerous read/write errors(similar to the first 130XE). I tried it with several different power supplies (just about every type of p/s except the big XE versions). Still no luck. Does the 512MB Transcend work any better with 130XEs? |
Author: | bf2k+ [ Sat Dec 13, 2008 1:19 am ] |
Post subject: | Re: timing issues |
_The Doctor__ wrote: Please make sure you 130XE's have the timing mod done and the sio pin 3 cap clipped.
Where are these mods documented? |
Author: | _The Doctor__ [ Sat Dec 13, 2008 4:01 am ] |
Post subject: | Re: timing issues |
try the three links listed above in the earlier post I you need more info or that does not do it... go here http://www.mathyvannisselroy.nl/blackbox.htm and scroll 3/4 of the way down till Isn't there a real solution? bf2k+ wrote: _The Doctor__ wrote: Please make sure you 130XE's have the timing mod done and the sio pin 3 cap clipped. Where are these mods documented? |
Author: | bf2k+ [ Sat Dec 13, 2008 10:00 am ] |
Post subject: | Re: timing issues |
Duhh.. how did I miss that?? _The Doctor__ wrote: try the three links listed above in the earlier post
I you need more info or that does not do it... go here http://www.mathyvannisselroy.nl/blackbox.htm and scroll 3/4 of the way down till Isn't there a real solution? bf2k+ wrote: _The Doctor__ wrote: Please make sure you 130XE's have the timing mod done and the sio pin 3 cap clipped. Where are these mods documented? |
Author: | _The Doctor__ [ Sat Dec 13, 2008 2:24 pm ] |
Post subject: | Re: timing issues |
We were following each other around, so while I was editing you were reading. I was verifying the links while you were posting. lol As you were posting I was inserting the links. The original time stamp was seconds apart. Cool! bf2k+ wrote: Duhh.. how did I miss that??
_The Doctor__ wrote: try the three links listed above in the earlier post I you need more info or that does not do it... go here http://www.mathyvannisselroy.nl/blackbox.htm and scroll 3/4 of the way down till Isn't there a real solution? bf2k+ wrote: _The Doctor__ wrote: Please make sure you 130XE's have the timing mod done and the sio pin 3 cap clipped. Where are these mods documented? |
Author: | bf2k+ [ Sat Dec 13, 2008 3:56 pm ] |
Post subject: | Re: timing issues |
_The Doctor__ wrote: We were following each other around, so while I was editing you were reading. I was verifying the links while you were posting. lol As you were posting I was inserting the links. The original time stamp was seconds apart. Cool!
Whew... I thought I was hallucinating again!!!! |
Author: | ponderosa [ Wed Dec 17, 2008 2:45 pm ] |
Post subject: | |
Both of the 130XEs that I tried this on had the same problem. However, neither one of them had any trouble with a CF to IDE adapter and a 64MB CF card. I can understand that timing might cause some problems, but it seems the IDE modules seem to be more sensitive to this issue than the CF adapter / CF card combination. I wonder why this is. By the way, one of the 130XEs appears to have been manufactured in 1990. |
Author: | mr-atari [ Tue Dec 23, 2008 5:20 am ] |
Post subject: | |
Hi, I know the problems you have. Most of the time it's a PSU-issue. Some memory modules are more power-sensitive then others and give problems on expanded machines. Best is to use a external 5 volt to power the memory module. Sometimes it's a good idea to clean the cartridge-slot (dirty contacts lower the voltage to the cartridge). But sometimes it just won't work, a typical atari issue...... You need to switch to a different atari or module. I have the least (almost none) problems with internal MyIDE on ANY system using ANY type of IDE hardware. Cheers, Sijmen. |
Author: | thewhiz [ Mon May 25, 2009 3:48 pm ] |
Post subject: | |
Was it compatible?: NO Manufacturer: Transcend Media Type: Compact Flash IDE Module Model Number: 256 MB (vertical) Capacity: (Labelled capacity) 256 MB Interface: MyIDE+1MbFlash Notes: Tried this in two XE's and one XL using the MyIDE Flash Cart. Sometimes will partially work, but writing to the cart always ends in Error 163 (MyDos). Tried two of these modules with same results. Used both internal and external power. Both modules work perfectly with KMK-JZ IDE interface. |
Author: | mr-atari [ Tue May 26, 2009 9:01 am ] |
Post subject: | |
thewhiz wrote: Was it compatible?: NO
Manufacturer: Transcend Media Type: Compact Flash IDE Module Model Number: 256 MB (vertical) Capacity: (Labelled capacity) 256 MB Interface: MyIDE+1MbFlash Notes: Tried this in two XE's and one XL using the MyIDE Flash Cart. Sometimes will partially work, but writing to the cart always ends in Error 163 (MyDos). Tried two of these modules with same results. Used both internal and external power. Both modules work perfectly with KMK-JZ IDE interface. Could be a MyIDE-cartridge issue. If you have a 74F245 onboard, please consult Steve Tucker. Also try the 4.4F beta OS. The IDE routines are changed to give better compatibility. Cheers, Sijmen. |
Author: | thewhiz [ Wed Jun 03, 2009 10:43 am ] |
Post subject: | |
mr-atari wrote: Could be a MyIDE-cartridge issue. If you have a 74F245 onboard, please consult Steve Tucker. Also try the 4.4F beta OS. The IDE routines are changed to give better compatibility. Cheers, Sijmen. Hi Sijmen- Thanks for the cart tip. It has a 74F245PC. Is that what you are referring to, or just a regular 74F245? (I did send a note to Steve, though) -Larry |
Author: | Tec [ Tue Dec 15, 2009 1:12 am ] |
Post subject: | |
RemoWilliams wrote: Was it compatible?: Yes
Manufacturer: Transcend Media Type: IDE Flash Module Model Number: TS2GDOM40V Capacity: 2GB Supplied with pin 20 power from cart. Unfortunately, I ordered and received one of these modules and have had no luck, never getting past HD ERROR! and dropping back to basic. I have tried powering it both via pin 20 and externally. Also, as it appeared to have corrupt partition table data, I also mounted it on a PC and zero'd sector 0 on it to make sure there was no partition data. My MyIDE internal interface works with a Syba(?) CD-to-IDE adapter, so presumably that's fine. Unfortunate - I really wanted to get this working so it could be internally installed on the 800xl. |
Author: | thewhiz [ Fri Jun 04, 2010 2:53 am ] |
Post subject: | Re: timing issues |
This is a really old message, but I believe the "original" documentation for this SIO/cap issue is in the Happy 1050 installation manual CIRCA 1984/5. -Larry bf2k+ wrote: _The Doctor__ wrote: We were following each other around, so while I was editing you were reading. I was verifying the links while you were posting. lol As you were posting I was inserting the links. The original time stamp was seconds apart. Cool! Whew... I thought I was hallucinating again!!!! |
Page 2 of 3 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |