Visit Atarimax Store


Free-Net Logo
The Atari SIG Historical Archive
Created and hosted by: atarimax.com
[ HOME | GO ATARI | 8-BIT | ST/TT | PORTFOLIO | LYNX | JAGUAR | LIBRARY ]


Article #57 (75 is last):
From: aa700@cleveland.Freenet.Edu (Michael Current)
Newsgroups: freenet.sci.comp.atari.prog.8bit.resource
Subject: Reading the Atari trak Ball and Driving Paddles
Reply-To: aa700@cleveland.Freenet.Edu (Michael Current)
Posted-By: xx004 (Atari SIG)
Date: Sat Jan 25 18:49:56 1997


Date: Tue, 5 Nov 1996 00:35:37 -0800
From: Barry Gordon 


READING THE ATARI TRAK BALL AND DRIVING PADDLES


      Both the Atari Trak Ball (in native "Trak Ball mode") and the Atari
Driving Paddles have a special characteristic which makes them superior
controllers. Not only can you read the direction they are being rotated,
but you can also determine the speed they are spinning. I will explain in
technical detail how to read each one. You must understand the Binary
numbering system and how the computer uses it to follow the examples.



Driving Paddles
------- -------

     The Driving Paddles have two physical characteristics which separate
them from the standard Paddles:

1) There is only one Driving Paddle per connector.
2) The Driving Paddles have no "end".
   (They can spin limitless in either direction)

     To read a Driving Paddle, simply read the Joystick register where the
Paddle is plugged in. The lower four bits of the register are used
(similar to reading a Joystick).

b b b b b b b b
7 6 5 4 3 2 1 0
- - - - - - - -
0 0 0 0 1 1 y y

     Bits b7-b4 are always zero. Bits b3 an b2 will always be 1. Bits b1
and b0 are used to determine the direction and rotation speed. When the
Paddle is rotated to the right, b1 and b2 cycle through the following
pattern:

yy =  00  10  11  01

     When the Paddle is rotated to the left, b1 and b2 cycle through the
following pattern:

yy =  00  01  11  10

     The speed at which the lowest bits rotate depends on the speed the
Paddle is turned. To put it in a decimal example, if a Paddle was plugged
into the first controller port, and being rotated to the right, the Basic
function STICK(0) would cycle through the values 12, 14, 15, 13.

     The button on the Driving Paddle is read with the Joystick button
register.



Trak Ball
---- ----

     The Atari Trak Ball is a versatile controller in that it can run in
its native "Trak Ball mode", as well as emulating a Joystick for
compatibility with games not written specifically for a Trak Ball.

     Reading a Trak Ball in Joystick emulation mode is identical to
reading a Joystick. The lower four bits correspond to the four directions
the Joystick may be pushed toward:

b b b b b b b b
7 6 5 4 3 2 1 0
- - - - - - - -
0 0 0 0 r l d u

     Bits b7-b4 are always zero. Bits b0-b3 are set to 1 when the Joystick
is centered, and cleared to 0 when the Joystick is pushed (r)ight, (l)eft,
(d)own, (u)p or any combination of these directions.

     When the Trak Ball is switched to its native mode, the same bits are
used, but in a different way:

b b b b b b b b
7 6 5 4 3 2 1 0
- - - - - - - -
0 0 0 0 v v h h
        m d m d

     Bit b0 is the horizontal direction bit. When the Ball is spun to the
left, b0 is 1. When the Ball is spun to the right, b0 is 0. Bit b1 is the
horizontal movement bit. As the ball is spun horizontally (left or right),
b1 toggles between 0 an 1. The faster the Ball is spun, the faster b1
toggles.

     Bit b2 is the vertical direction bit. When the Ball is spun upwards,
b2 is 1. When the Ball is spun downwards, b2 is 0. Bit b3 is the vertical
movement bit. As the ball is spun vertically (up or down), b3 toggles
between 0 an 1. The faster the Ball is spun, the faster b3 toggles.

     Here is the direction information in another format:


      b b b b            b b b b
      3 2 1 0            3 2 1 0
      -------            -------
      0                      0  
Up    1 1 x x      Right x x 1 0

      0                      0  
Down  1 0 x x      Left  x x 1 1

     To put it in some decimal examples, if the Trak Ball were being spun
to the left, the LOWEST TWO BITS would toggle between 1 and 3. If the Trak
Ball were being spun downward, the HIGHER TWO BITS would toggle between 0
and 8.

      It is very important that when reading one set of direction bits,
the other two direction bits be masked out. Both sets of bits operate
independently and will confuse your readings if you are looking for a
simple decimal number from the STICK() register.

     Both buttons on the Trak Ball are read with the Joystick button
register.




Barry Gordon                  
6/28/90                       

------------------------------
-- 
Michael Current, 8-Bit Atari FAQ & Vendor/Developer Lists maintainer
   User groups: CAIN, SPACE, NWPAC / mailto:mcurrent@carleton.edu


Visit Atarimax Store